Automotive obd2 scanner suspension modification process

1. Hanging the SETTING tough it will backfire?

Overly hard to tune the suspension in addition to make  obd2 scanner the frame twist, accelerated aging, and multiple noises, but also may cause traffic accidents. Pass through the irregular road surface when the vehicle speed at any time not to play because of the shock absorbers should be the role of a result of the wheels off the ground, took place in the corner on the way, the vehicle they may get out of control and lead to traffic accidents.

2 hanging too low, there will be problems?

This indicates that the vibration-damping sleeve travel is reduced, relative to the ability to cope with the pavement fluctuating dropped. Low ground away from the body Qunjiao, dead air hose easily touch the underground, and out of the parking lot or sudden deceleration would be very inconvenient.

In addition, the lower body, four geometric angle will change more than 20mm, affect driving straight or handling, and therefore need to re-make the wheel alignment adjustment may also need to adjust the CAMBERANGLE avoid touching the sand board.

The unscrewing shock a crime?

If the suspension upward activities, the wheel does not touch the edge of the fender, and reduce the body so that the suspension  elm327 arm drooping slingshot from prop can be through the vehicle inspection.

4. Bobbed slingshot feasible?

Bobbed slingshot is the older generation to change a short body off the ground from the way, because the cheapest, the fastest, but it is a very dangerous practice.

Bobbed slingshot, the vehicle ran rough roads, if the shock absorbers stretch best body sink away from the prop will be sharp slingshot incision break on or under the slingshot prop or position appears break the high-speed operation of the tire, so the cut slingshot is very dangerous.

The 5.ANTI-ROLLBAR what?

The ANTI-ROLLBAR commonly known as lexia 3  "shrimp", and one was a U-shaped metal U, each connected at both ends of the left and right rocker arm, focus manipulative models typically the front and rear wheels will be installed on. The aim is to side rocker arm upward shrink in the vehicle when cornering at the same time, through the anti-roll U other side of the suspension along with compression, so the body will not be a one-way side kneel, to maintain body balance to increase the limit of the bends.

New drivers shift Auto Diagnostic Tool eight Note

More and more new drivers on the road, the back of Auto Diagnostic Tool    the car close to the "novice", "run" everywhere. That new drivers on the road will encounter a variety of challenges.

: Shift looked down shift lever.

: For a long time with a low gear driving. In general, high-speed block than low gear fuel efficient. Therefore, after the start should be timely upshifts.

: Shifting clutch riding does not in the end, causing gear damage. In addition, do not use the clutch feet should not be placed on the clutch to cause release bearing excessive wear.

: Shift the direction of the deviation.

Five: When the time can not be exchanged into gear is hard push deadlift.

Six: When the shift lever to neutral and fro. Likely to cause mechanical unnecessary wear and affect the timing of the shift.
7: leapfrog plus gear. Plus gear should be carried out step by step, to prevent the vehicle power is not continuous, downshifts can leapfrog.

Eight: the car is not parked hanging reverse gear. Likely to cause gear damage.

How to dress up your car Vag Com Usb Kkl Interface

And plastic break up the seam and molding. Molding Vag Com Usb Kkl Interface and plastic disposable pressed into, with the car manufacturer's trademark. No seams, waterproof, dustproof better. But for the ups and downs of the larger car floor, laying molding and plastic appearance is somewhat less certain. Hand-stitched and plastic flatness, more colors can be selected, the same can effectively prevent dust and other debris into the carpet, the waterproof ability somewhat less. Sew-and plastic can also choose a different thickness, the 2mm and 3mm points, Shop thick and plastic, wear resistance and sound insulation will be better.
Cost-effective electronic security
The car burglar divided three forms of mechanical, electronic and network.
Gear Locks mechanical anti-theft mainstream products, the identity of the owners of the simple, solid, suitable for a variety of manual transmission cars. Electronic anti-theft devices in the market, the most common password to unlock and the alarm sound is its biggest advantage. Electronic security devices at the same time both the car search, door not shut prompted, with the central control remote control to open the door locks also has a good price. The network is more advanced anti-theft device, using GPS base station can achieve positioning, communications, surveillance, suspension of service, scheduling, and other functions, but expensive, luxury cars more installing this type of anti-theft products.
Winter film would be reimbursed for the "benefit"
Winter is the low season  Audi Vag Com Cable of the foil, the owner can take the opportunity to ask for more concessions to the store.
The film must be in a clean room operation, side window film before and after the windshield film should paste the whole piece. Asked the store owner to cut a few test paste, you can choose the color of the film. Observe the imitation pseudo mark whether the explosion-proof membrane.
Brand-name radar shelf life of three years
The increase in the number of cars, parking spaces can not increase, reversing problems plagued the novice. Reversing radar, so the novice can readily understand the distance and obstructions, freely reversing into place.
LCD and progressive shortness tone so drivers do not have to go back to about the size of the space after the car; quality probe cast iron bumper probe can be avoided and installation experience, drivers can avoid the low stairs and railings,reversing. The radar can be installed multiple probes, mature installation technician will avoid confusion sensor harness wound, try drilling is not the body of the  Vag Com Usb Cable vehicle to reduce the damage to the body, to prevent corrosion.

Car film purchase and use of renault can clip skills

 A wide variety of market car film, the  renault can clip quality varies greatly. The layman's owners Accidentally inevitably deceived spend a high price to buy a poor quality film or fake. As everyone knows, the poor quality film not only endanger traffic safety, also easily lead to the glass hidden dangers and even affect the health of occupants. The owners decided to give their car foil, be sure to pay attention to in the purchase from the following to distinguish authenticity of explosion-proof film.
1, clarity. The quality film transmittance up to 70%, block the film up to the light transmittance of more than 80% of the such as Monarch of carbon gold heat proof film SK80 ago, the night clearly saw six meters away from the items will be fog and poor quality film misty feeling;, feel. Genuine film feels a thick smooth feel inferior film feel thin and crisp, wrinkle easily; 3 colors. Quality film of pigment is evenly fusion in the film, durable, easy to change color, and inferior color film in play a bonding role in the bonding glue, tear the membrane lining of the car with a fingernail scratch, the color is off; 4 , taste. The inferior film layer residual solvent benzene content, smell, would seriously endanger the health of the owners; 5 bubbles. After tearing the plastic lining of the car film, re-composite, low-quality film will blister, and high-quality film composite after intact; 6 shelf life. General formal manufacturers film has a long quality guarantee period, Monarch insulation explosion-proof film, the warranty period is up to 10 years.
● Paster stores, formal requirements
Good product is important, but the process of the film can not be ignored. Select high credibility, good service  VAS 5054A  stores crucial. Regular car beauty shop with a professional film workshop, because the film process must ensure a relatively dust-free, cool. The owners do in order to save money, to choose some roadside shops and even choose not fly unscrupulous business practices, it will not only cause the film quality below standard, may also be some damage to the car body and car glass, more harm than good. Street job is difficult to do because the film most afraid of dust and gravel, clean environment.
Automotive beauty shop owners in foil before Look around, see if the store is clean, the ground is clean? Do you have the authorization certificate of explosion-proof solar film manufacturers? The film technicians service level whether to cross the border? Whether to set a special foil construction workshop? The workshop has the spray dustfall device? Are foil car can also look at the construction process, the construction process is smooth and precise?

Before the film, the first response car facilities to protect the seat and the dashboard is covered with plastic wrap. Foil, avoid using easy to make film  mb star c3 faded lubricant, can not film in the case of direct sunlight, because the film so affixed to wrinkle easily blistering, greatly affect the car's image of beautiful.

Winter car must through the snow icy road to safe driving

The snow drive or icy roads, to calm careful. Traveling slow,  http://obd2demi.blogbaker.com/ involuntary overtaking, tap the throttle, tap the brakes, slow play direction, any action or inappropriate action potential danger.
If necessary, the tire may be to put some gas, increases the contact area of ​​the car with ice slippery pavement, enhanced tire adhesion; icy and snowy roads at any time should slowly lift the clutch slowly refueling vigorously refueling easy sliding or idle; Remember to maintain the distance between vehicles , the brakes or start, front and rear vehicle may slip car or sliding.
Dark, dank place under the overpass and tunnel entrance, etc. are easy to freeze, thin ice is more frightening, should be cautious, slow down.
Icy road is the most dangerous situation drivers may encounter. In this case, try to travel in the ruts left by the previous car, do not rely on roadside driving. If you feel the drive wheels start to slip, and immediately release  the throttle. Increase with distance from the vehicle in front, and to maintain at least ten seconds. Do  http://lexia3.blogcu.com/ not slam on the brakes, as is likely to cause skidding. If skidding immediately release the brakes, the steering wheel to regain control of the car.
Snow driving to increase with distance from the vehicle in front, to advance to the brakes. When found and the distance of the vehicle in front shortened for whatever reason immediately the oil revenues deceleration ready to brake and foot on the brake pedal, do not leave things to chance, careless.
Traffic safety experts said that the normal dry asphalt road surface friction coefficient of 0.6, the the rainy road surface friction coefficient is reduced to 0.4 compared to 0.28, snow, icy roads is even lower, only 0.18. The friction coefficient reduced braking distances increase, wet-weather drivers like normal road car, it is easy to rear-end collision. So the driver to increase the distance between vehicles, to extend the braking distance.
Try to avoid parking in the snow, because you make it difficult to restart. If it is necessary to ensure that there is http://lexia3demi.quebecblogue.com/  enough space to leave the parking spaces in front and rear the mobile parking spaces become very difficult in the snow downhill parking.
Snow after car tips
. Started the process of moving prohibited fierce lift the clutch, hard acceleration, braking, should stabilize the throttle constant speed, downshift method should be used for the vehicle to slow down and use engine braking.

The remote autoboss v30 returned knowledge

Expect to be rewarded when traveling long distance by car owners and to the satisfaction toiled car? It was just the car needs extra care when finishing stricken and weary car, sooner rather than later.
First of all, from the internal start. Countryside dirt road, especially long distances or go to their place after wilderness, vehicle pollution is serious, came back, and the best time to clean the inlet, fuel injectors and carburetor, if the driving environment is dirty, the need to Clean or replace the air filter.
Also, check the oil, brake oil, if any is missing to replenish. Too dirty, then the need to replace the new oil and a new filter. Check the chassis for oil spills, water leakage; Check the tire pressure and wear condition, with or without nuts loose or fall off. If the deviation or playing swing, driving up to redo wheel alignment or dynamic balance.
Check the fan belt for damage or breakage, adjust the tightness of the belt. Check brake pedal is too loose and weak, reserve too little trip, said leakage or brake failure, the need for timely excluded.
Finally, the need to pay special attention to the spring flying catkins or flowers and other debris flew into the radiator in motion easy film, resulting in poor heat dissipation, affecting the normal operation of the machine and the air conditioning and refrigeration. Excursion back to rinse.
After returning to paint care essential nature.

What is wheel horsepower / power

As we all know, the gasoline engine petrol chemical energy into heat energy, then part of the heat energy into mechanical energy is used to drive the vehicle. Modified cars increase horsepower means firstly, to increase the amount of fuel injection, is to improve the efficiency of automobile engines (engine efficiency, the engine efficiency of converting thermal energy into kinetic energy), both a positive and auxiliary means. In fact, heat engine is not a very satisfactory way of working, because a large part of the energy emitted by the form of heat into the air. The rest converted into kinetic energy but also as a generator, hydraulic power agencies, as well as the cooling system and air conditioning equipment to provide power to get that part of the power they need, etc. These devices, and the rest from the crankshaft output is power used to drive the vehicle, most car manufacturers in promoting the nominal dynamic .

 The transfer of power is not over yet, from the engine crankshaft to the car's tires ultimately counterproductive to the ground is full of gear and bearing long journey. Imagine, the first clutch or torque converter and gearbox, final drive, differential, axle, and finally to the wheels, the power to the ground by the tire ... in this process, the power because friction loss after these pass final role of power in the ground is that we really can be used to power, power wheel.

     
So how this really can be used to wheel power measured? The answer is dynamometer! The dynamometer's main purpose is to measure the car wheel output power test car glide performance, test vehicle acceleration performance, check the speedometer, equipped with a fuel consumption meter chassis dynamometer can also simulate the road, measuring fuel consumption constant. So conditional modified car finished their car do not forget measured wheel power Oh, we can engine power increase to the number of ways to improve gearbox, final mechanical energy losses in power transmission will make us feel bad · · · ·

Spraying and installation of the guard Autel MaxiDAS DS708

1. Guard plate under the engine installed but no harm!

2. Engine under shield will not hinder subsidence engine after the accident!

3. The engine under the guard will not affect engine cooling, and will not increase fuel consumption!

    Why? I will listen to you, 20 pounds of  Autel MaxiDAS DS708 the weight of the engine guard thickness of 3-5 mm, installation the effective tissue foreign bodies hit the bottom of the engine, protect the oil pan from impact damage! The engine weight sinking vehicle accident can fall to the ground under the impact shield only four screws under guard how likely bearing the weight of the engine? That installed affect the cooling of the engine under shield friends, I can only say that your idea of ​​a good laugh! Open car, driving there is wind, the wind is the best heat installed under guard not sealed the bottom of the vehicle? How to influence the heat a say? Is not it? Yes and no, you testify! I only try to explain in plain words the guard mounted engine is good! More than a hundred dollars can avoid the loss of a few thousand, what is wrong?

    I think what the top of my butt! Bang, thump, slightly La la la la, no way! Followed by cars long, yellow sand, stop can not stop, forward only reluctantly, car pain, I felt, to bear the pain! Road car did not feel strange, opened ds708 scanner abnormal sound! Returned to Shenzhen, the first time the car wash, the second time-liter car, look at the bottom of the vehicle immediately! Ha ha!

    Thanks to bottom protection Invincible Iron underpants! Seeing is iron underpants life and spend up to 5,6 at the hole than half a millimeter in depth, it is deep, deep friends! The exhaust pipe cooling aluminum angle is broken! Exhaust pipe deflated a pit! Car chassis at the protective armor was scratched many other little effect! Ha ha ha ha ha ha! This invincible iron underpants or play a good protective effect for it! Places  MaxiDAS DS708 worthy of promotion to the broad masses of the people Well!

Four-wheel drive off-road vehicles OBDII Circuit Board

Switch to supporting suspension conversion kit, elevated  OBDII Circuit Board chassis ground spacing to increase the vehicle's approach angle and departure angle, approach and departure angles larger the vehicle through better. Generally people will kind of misunderstanding is that the chassis ground pitch rise higher off-road capability more. In fact, please do not forget to off-road vehicles to travel big gap in the pavement around the body on both sides or pit wow the chassis ground spacing liter higher, the higher the center of gravity of the body, the easier vehicles turning side, or even overturned, be able to safely pass through the same conditions as the road speed immediately dropped. Chassis off the ground spacing between the center of gravity of the body, it is necessary to strike a balance.

    General chassis level rise will depend on the use, usually used in ordinary street vehicles moving generally take 2 to 3 inches higher suite, and increased slightly more technical players will car owners converted 4 to 5 inches, 6 inches above has been regarded as very professional and crazy modifications. At the same time elevated OBDII Code Info reduced efficiency of transmission system, increase the vertical height of the main reducer gearbox, drive shaft will also increase with the angle between the horizontal plane, not only will the loss of a certain power, at the same time will also increase the wear on the machinery. Usually professional practice interested in the location of the engine and gearbox to be adjusted for the slightly inclined, but the required action is very cumbersome.

    Increase suspension travel

    Bumpy mountain road, how to keep the four car theory has always been close to the ground, which is one of the very important indicator to measure the four-wheel drive off-road ability level in the game, we usually off-road vehicles can be seen through an extremely bumpy track four suspension constantly respective elongation and compression, the wheels Wholesale obd2 tools always stay on the ground, the amplitude of body roll but small, the action is very elegant. This is the long suspension travel's sake.

How to identify Ford VCM Solar Films

Summer car, sun exposure will not only burns the  Ford VCM driver's skin to ultraviolet light may also burns car interiors, so some leather aging. Increased car interior temperature, the air conditioner to improve the frequency of use, increased fuel consumption, so the foil is very necessary. Film more types of the car market, the quality is uneven. So when choosing a car film to master certain methods of identification.
See clarity
High-quality car film clarity at night should be more than six meters, and the poor quality of film clarity is poor, especially in the line of sight of the night, both sides and rear windscreen is unclear.
Feel
Quality film feels a thick, smooth feel, poor quality film feel thin and crisp, easy to wrinkle.
Color
The high-quality film of pigment is dissolved and the car film, durable, easy to change color, scraping blade coating paste  Ford VCM Ids  process will not decolorization. Inferior film color glue, tear the membrane lining of the car with a fingernail scratch, the color is off, the diaphragm is nails scratched the place will become transparent. Foil process, when the scraping scraper film, sometimes color off on their own, this film then will change color, bleaching becomes more apparent after one year.
Bubble
Tear the car film plastic lined, and then recombine inferior film will blister, and high-quality film composite after intact.
Insulation properties
The insulation is an important indicator of the solar film it with the naked eye and feel is difficult to identify. Through a simple test method for comparison: put a close to the glass of the car film in an iodine-tungsten lamp, hand feeling no sign of heat  GM Tech2 is a high-quality film, immediately indicates that hot feeling its thermal insulation The problem is a bad film.

Pay attentio to BMW GT1 car lights

Nocturnal lights, signal lights, fog lights, nocturnal BMW GT1  lights and other lights in the car the ministries lights each with different purposes, the use of very particular about, neither indiscriminate use nor not.The width light nocturnal, commonly known as the "little lights". This light is used at night and displays the body width and length. Regular checks of drivers usually carry out routine maintenance some drivers think small lamp can not afford to lighting effects, its not enough emphasis on this is very wrong.Lights, including turn signals (double flash) and brake lights. Proper use of the signal light is very important for safe driving.Said first turn signal lamp is opened in a vehicle steering, intermittent flashing to vehicles and pedestrians around the prompt attention. Turning lights turn-on time to master, should open away from turning the intersection 100 meters. Open prematurely give car caused the illusion forgets to turn off Turn the open too party trailing behind the vehicle, pedestrian unprepared, often busy in error.Talk about the brake lights, lamp brightness  Autocom cdp pro  strong, used to inform the car, the first car to slow down or stop lights such as improper use can easily cause a rear-end accident. In addition, to remind the driver to replace the brake light bulb should pay attention to: the taillights of vehicles produced in China are generally a bubble with two, two light bulb filament, weaker small light, strong brake lights. Some manufacturers to design for the high and low-pin plug-in, it is very convenient to use. The replacement must be careful not to reverse.Fog lamps, it can help the driver improve visibility in fog while driving, and to ensure across the car to discover, to take measures to safe rendezvous. So, while driving in fog drivers must open fog lamps, and small lights can not be replaced.Night lights, commonly known as the "headlights". Headlights is the "heart" of the site for the full headlights. Reasonable use of headlamps should do the car becomes nearly light, the car will change back in time to high beam, to put far sight, make up will be car caused blurred. Through the intersection and overtaking should be to transform the distance light to prompt.Some drivers use BMW OPS DIS V57  headlights as a "weapon", according chaos chaos "sweeping. This case the number the rural "three" and "four". Many farmers drivers often sneak in at night to take advantage of without checking the road, completely ignoring their own "black ass" is unusually sharp, in front of headlights. Their headlights irradiation angle generally have been "fine-tuning", the purpose is not to light the way but according to the car. This is very dangerous, was not to be taken lightly.

Autocom CDP Pro turbo conversion foundation: Overview and turbine body

Turbo intake in the form of a mandatory intake air above an atmospheric pressure into the cylinder, the density of air molecules than the naturally aspirated cylinder, which can produce a stronger power, and large-scale applications. The first turbocharger driven by exhaust gas by the Swiss Dr. Alfred Buchi study in 1909, after years of development, the main structure and principles are no major changes. Installation of the turbine or turbo car modified for the naturally aspirated models, based modification involves the following main components: turbine body (length) exhaust header banana, intercooler, intake pressure relief valve and drain gas pressure relief valve. In addition, for turbine modifications, we also should be aware of some turbine parameters so that we can grasp the magnitude of the turbine modification. 
Gasoline works every 1 kg of gasoline inside the cylinders, cylinder inhalation takes about 15 kilograms of air and to guarantee gasoline combustion. 15 kg of air, however, its volume is very large, and rely on the cylinder in the engine intake process the degree of vacuum is not easy to such a large volume of air inhaled. Engine since the oil pump, fuel pump, water pump, power steering pump, used to "move" the equipment of a variety of liquids, why not to add an "air pump" can exist? Ever since the "air pump" - turbine body appeared. The turbine body equivalent to a blower, the pressure of the more fresh air into the engine combustion chamber, improved combustion efficiency, thereby improving the power output in the case does not change the working volume of the engine. 
Since the turbine main body is an "air pump" We are familiar with the pump mostly through the motor to provide power to drive the blades to rotate, while the turbine body is using the exhaust gas after combustion to promote the blade compressing angry way pressurizing. Such a pressurized manner, there is no additional energy consumption, but it has excellent power per liter of performance relative to the NA of the car of the same power, the same power output data and non-extreme use conditions, the fuel consumption may not be higher than the NA car.  

Simple statement of the principle, nothing more than the use of the heat generated by the engine after the explosion stroke, high-speed energy of the exhaust gas, the exhaust gas discharged from the cylinder through the special shape of the exhaust banana (DOWN PIPE) flows into the exhaust side of the turbine, and push the exhaust side within the turbine blades rotate, while coaxially connected gas-side compression impeller, interested flowing styles gas compression, and the compressed gas, and the exhaust gas side of the turbine blade with a certain pressure through the central cooler (INTERCOOLER) After cooling, the and high density fresh air, after flowing through the throttle valve and the intake manifold into the cylinder combustion.

How to distinguish sedan four-wheel obd2 tool technology

With the addition of cars the listing of Zexi, equipment four-wheel obd2 tool drive system a choice. Technological development we are not allowed to say that, who knows the day sedan four-wheel drive and turbo, like sweeping the globe? After all, the winning vehicles from the 1982 World Rally Championship are full-time four-wheel drive car. So we come to discuss the technology to discuss the four-wheel drive cars.First, the center differentialIf your brother does not know the "differential" This stuff that need to go to make up classes, this article does not go into this. The role of the central differential with the differential is the same reason, the differential is in order to allow both sides of the wheels to rotate at different speeds, and the central differential is in order to allow two anteroposterior axis to operate at different speeds.The four-wheel-drive sedan is necessarily a center differential (off-road vehicles may not necessarily). The center differential is the hub of the four-wheel drive system, the role of the engine power distribution to the front and rear axles, similar to the "waist" waist good kidney good legs and feet, not to say okay, is the same reason. Waist Yi Yao water bucket waist, waistline, and so on and so  Auto Diagnostic Tool forth. Center differential are many ministries the same features, and even the center differential that his title has become less and less used. For as long as it is assigned to the core components of the front and rear axle torque, we still can not understand it as a center differential differential.1, full-time or timely. For full-time or timely, of course we can not listen to the name to determine, but this is well understood. Full-time is characterized by at any moment are allocated on four wheels, and timely are generally in some cases (usually occurs wheelspin) connected to four-wheel drive system.2, the transfer of power of the front and rear axle ratio range is large enough. Typical example Zexi front-wheel drive, the rear axle most torque distribution of 50%, the Acura rear axle can get up to 70 percent of the torque distribution, allocation of torque front and rear axle of the Audi Quattro system can be 15% - varied between 85% and Tiguan 4motion system torque distribution between 0-50%.3, the response speed. Since the structure and principle of the same, the response speed of each of the central differential is not the same. Called the response rate is very professional and that, in fact, the young man he thought of as a loss of balance, fast response can not fall immediately adjust the center of gravity, slow reaction will be to shoot directly. The car's four-wheel drive system on the reaction rate is higher than the cross-country. The sedan is the moment things got out of control at high speeds, the response speed is fast enough, you can get out of control impending four control,  lexia 3 v47  rather than waiting out of control (slip) and then attempt to control.
Audi Quattro is the famous center differential Torsen differential. Since using the principles of the purely mechanical force distribution, like differential is an innate physical properties, and therefore no reaction time can be automatically assigned the torque to the front and rear wheels. Audi is also often in the hall on the hanging cited thought proud of gecko logo reasons.

How BMW Airbag original and non-original modifications improve braking capacity

How modifications to improve braking ability
    The basic principle of the brake energy of rotation of the wheels by the friction of the brake pads into heat, then heat emitted to air brake discs. Strengthen friction and heat capacity, the brake  BMW Airbag ability will enhance the modified product is designed for these two points. Want to significantly enhance braking performance, and then to increase the size of the disc, while the modified version of the brake pads is worth considering.
    Hydraulic brake calipers
    Original and non-original categories are available
    Modified brake calipers on the market is divided into two categories of original and non-original. Original product usually with a larger diameter, or a plurality of caliper piston design, because the liquid learn the fixed rate, passive larger the area of the piston, the pressure will be greater, also increases the pressure of the brake pads,  Airbag Reset the braking capacity corresponding increase multiple piston design is also the same reason. Similarly, liquid fixed rate science driven piston area increased, the amount of liquid needed increases will therefore growth put pressure on the piston stroke, the stroke of the brake pedal a little more light weight, a little.
    Non-genuine brake calipers, almost all racing use products, and multi-piston design, installation must meet the special adapter bracket commonly known as the "bridge". To such products in addition to the Pistons put pressure area larger weight are particularly light, can reduce suspension weight and speed up the suspension of activities speed. With the larger diameter brake discs These lightweight  Opel Airbag Reseter calipers can be offset by the increased weight of the brake disc.

Autel MaxiDAS DS708 beauty and car modification Mistakes

1. Changed big exhaust ---- reduce Autel MaxiDAS DS708 exhaust back pressure, low torque will drop, engine exhaust valves will be easy to burn because of the ultra-high temperature.
    2. Installed mushroom head ---- reduce the inertia of the air intake, The low torsional will decline, increased fuel consumption, low speed weakness.
    On balancing rod, tie rod ---- local vibration more severe, permanent damage to bodywork.
    Converted sound, plus subwoofer ---- must be dismantled interior parts, the demolition will surely fracture, a different degree of damage, car parts demolished once abnormal sound several times. The exaggerated volume subwoofer owners will unknowingly damage hearing, high-power audio often makes circuit overload, easy to burn the switch and cause a fire.
    Directly after the 5 plus gasoline, lubricant additives ----- the gasoline oil line cleaners will dissolve the impurities in the fuel filter clogged fuel injectors, oil additives only applies to moderate burning oil and old cars, any new car plus The inside will cause fever and severe wear.
    Change large tires ------ started weakness, accelerate slower, steering wheel-Agency accelerated wear.
    7. Installation of multi-point coarse ground ------ lead to abnormal high voltage line potential to shorten the life of Fireworks plug, sometimes confusing computer will increase fuel consumption.
    8 car perfume ------ almost all Volvo Vida Dice  chemical flavor, toxic, embrittlement corrosion on the interior plastic, will somehow burst a long time, good health and great harm. Stuck in the air conditioning vent perfume bottles often cut off from the outlet wind guide piece.
    9 the car door soundproof ----- must be dismantled within a decorative, keep in mind that the split will hurt. The soundproofed only vehicle production process to be completed, and can not tamper with. The silencer principle, not posted there, this is a problem of acoustic equalization offset. Often you every door would listen to the engine sound is more obvious every engine sound will lead to the car the abnormal sound sounds more messy. Demolished every time, there is always gong silky teeth lost or trim the plastic buckle broke. We have to understand the principle of professional and moral qualities of the people are different. Some posted on the Volvo Vida Dice 2012 door inside the tin, once the collision repair, it would psoriasis.

4 kinds of preliminary selection of lexia 3 modification

In fact, car modification there is no fixed pattern, as long lexia 3 as it can go and change according to their own imagination to go and eat it. This is a culture, a spirit, a kind of enjoyment, is also an understanding of the car. In the conversion process, the owner will be able to understand the basic performance of the car, to grasp more knowledge of cars and engines.
     Car modification constrained by three factors: the economic strength of the owners, the supply of modified parts and automotive annual appraisal system. Many people have started working on the car fitted with the new tricks, but the domestic still fresh operating professional conversion. Too specialized modification means that the high-cost, small-market, low adaptability.
     Modified car in two ways: to wear new clothes law and Phi sheepskin. Many nice sign posted in the body, so that cars such as the new fashion wear eye-catching, "The Emperor's New Clothes," a "wolf dressed in sheep's clothing" converted; still popular, the car's engine , driving performance improvements, and the appearance that does not move. Once encountered the same type of car, and immediately showed different performance.
   
      1 large flow air filter:
     The engine air filter air is needed in order to filter the engine running on gasoline engines have this device installed in the original car air filter seems to be in play car seem into the gas shortage suspected. So, play car modified intake system of practice.
     Many people think that the large flow air filter, high-speed operation of the engine intake air quantity is different, in fact, this argument is not very accurate. Because the size of the intake air will not change because of the modification of the air intake device, as long as the engine displacement does not change,  Auto Diagnostic Tool into the open-mindedness is not going to change, unless the use of the turbocharger. The principle is that the engine using a vacuum subpressure to let outside air enters inside the cylinder, but because the air is passed through the filter after entering the cylinder, so the resistance so that the air can not be completely the same pressure of the outside world into, and because the air is inertia, So the the converted air filter is a very critical step. Modified with the actual test, the engine at high speeds, the power increase, the engine is running smoothly, speed feeling good.
     Expert opinion
     Install flow air filter to try to stay away from the engine. Of the temperature of the air entering the engine as low as possible, only the low temperature to the high density; same time, the oxygen content will be increased slightly.
     If the engine is no suitable space around the installation can be separated from the engine and filter separator.
     Ordinary modified air filter for models at  Launch X431 GX3 different prices vary between 350-800 yuan float. 10,000 km to 30,000 km need to clean or replace, maintenance, replacement cheap.
    

Development of lexia 3 radio remote control driving technology

Since the automobile was born the day people imagine lexia 3 whether to let them run up security without intervention ongoing technical exploration, engineering research and development staff also A Hundred Years of automotive development and manufacturing, and finally in the 20th century a remote driving of prototype cars. After the birth of a variety of prototype cars, the technology is still always makes unmanned technology market-oriented exploration. August 2012, with the the BYD speed Rui listed on the world's first remote control technology to achieve driverless car market officially born.World Expo held in 1939, the American industrial designer Norman Bell Geddes exhibited a ground-breaking models in their own future urban theme exhibition. The car relies on the electromagnetic coil embedded in the pavement to provide power-driven, motorists radio remote control can be used to manipulate them. The entire car R & D has been GM's assistance, the car also became a historical a driverless technology car.Driverless car technologyNarrowly divided unmanned technology is the the vehicle completely rely on their own ability to travel, free from human intervention and manipulation in the whole process of moving. However, in view of the current level of technology, this unmanned technology is also exploring stage, a more limited range of practical Launch X431 GX3 applications. In broader terms, as long as the vehicles during the people in the car, or no direct control mechanism (steering wheel, accelerator and brake pedal by the vehicle itself) control vehicle technology can be called unmanned technology. This is one of the most widely used remote driving skills.RC driving skillsThe remotely piloted technology is nothing new, small remote control cars, large construction machinery or military UAV use this technology. View from the spread of the signal of the carrier is generally divided into radio remote control, infrared remote control and ultrasonic remote control. Household appliances remote control used in our daily lives is the infrared remote control, this technology uses infrared signal transmission, has the advantages of simple structure, convenient, low-cost production. But its remote shorter distances, and not be able to remote control signals pass through a barrier defects, and also vulnerable to interference problems when the sun is strong and more prominent, infrared remote is close remote, especially  obd2 tool indoor remote preferred.

The use of volvo vida dice manual transmission feelings

A transmission is good or bad, and the degree of matching it  volvo vida dice  with the engine, the vehicle dynamics and ride comfort have a direct impact. Compared to the market common AT automatic transmission CVT, DCT, AMT, traditional manual transmission, although the surface looks more "simple", "original", but in the cold mechanical components but also hidden a variety of mystery at the same time want to make one feel superior MT, has never been an easy task.The role of the transmission

   In general, the transmission is a capable of changing the speed, torque and direction of the rotary power of the automobile engine, and the driving force is transmitted to the transmission of an apparatus.
- Change the transmission ratio

    General, automobile engine by burning fuel to get power in the entire speed range of the engine, the output torque and power is always changing, from the vehicle driving force generated by the engine's torque can not rely solely on the meet the car driving to face all kinds of complicated road conditions. At the start or when climbing, for example, through the low gear transmission in the case of lower vehicle speed, the engine speed is pulled to output large torque. High-speed cruising of the vehicle, through the transmission of the high gear to reduce the rotational speed and torque output of the engine, thereby reducing fuel consumption. Due to the characteristics of modern engines, this is not perfect, the transmission came into being. Transmission using a different speed ratio at different operating conditions, thereby making the vehicle and the engine in various operating conditions can play its optimum dynamic performance.
- Provides reverse gearAn engine early in the design determines the direction of rotation of the crankshaft, so in order to make the vehicle backwards gm tech2 , and can only hope that the transmission through external gear reverse rotation characteristics can easily accomplish this mission.Reverse gear is why there is a special action?

    School car used manual transmission, some friend's car is a manual transmission, I believe we for the manual transmission as familiar as his right-hand man, I wonder if you have considered, the operation of certain manual transmission reverse gear there will be a special action, or to hold down a button on the shift lever, or to slightly lift the shift lever. Why is this? Is it just to handsome action, or make the reverse gear manual transmission need a set of very complex parts can be done? In fact, the principle is very simple, read the following named reverse locking mechanism that you will understand. 
In order to prevent mistaken hanging when the vehicle moves forward into reverse gear, and thus have a great impact on the  maxidas ds708 transmission gear, resulting in damage to components, usually on the manual transmission reverse gear locking mechanism design. When the shift lever is placed in the limit position, the stopper in the lock mechanism by the shutter block, the cause can not be mounted reverse gear. Reverse gear only hold down the button, the stopper can continue to move across the baffle, which hang into reverse gear.